Launch

The new NZ series of motorcycles was announced with two new models, a 250cc and a 350cc, for the first time in the DKW dealers bulletin of 28. Dec 1937. In the bulletin from 28 March 1938 the factory once again announced the launch of these new models and than the first NZs leave the factory in November 1938.

NZ 350 frame advertisement
NZ 350 frame advertisement

Early development

In this period the factory already experienced some problems with the lack of materials therefore the earlier announced features of the bikes as side-crutch and chain-box were not mounted on the first bikes. The chain-box was never adopted in this series.

NZ 350 gearbox advertisement
NZ 350 gearbox advertisement

Initially it was planned that the sides of the gas tank should be chrome plated. Shortly before the launch of the new models on the Berlin Kaiserdamm-Exibition in February 1938 the use of chrome on motorcycle tanks was banned. DKW then decided to spray the sides of the gas tank with melted aluminium, which was then polished.

DKW NZ 350
DKW NZ 350

Technical masterpiece

The new NZ series was the result of years of long technical research and innovations in the DKW's research centre. New revolutionary pressed-steel mainframe - Zentralkastenrahmen, more beautiful engine block, four speed gearbox, new starter mechanism, are the main characteristic features of this new civil motorcycle.

The mainframe itself was a masterpiece of engineering: made from  two pressed steel sheets which were electrically welded together. Unfortunately the welding process used so much electricity, that the welding could only be done at night, when the electrical consumption of the other parts of town were lower. 

Frame welding in DKW factories

Initially it was planned to supply the NZ with a rear suspension. Extensive tests were made and a suspension was chosen which was already patented by the Italian manufacturer Benelli. When it became clear that royalties had to be paid to Benelli, the rear suspension had to be omitted for costing reasons. Nevertheless about 1100 NZ's were supplied with Benelli rear suspension, but were only supplied to the government organisation NSKK.

In the beginning the central electric box was of type Sp12A, which had the ignition key hole blanked, it was replaced in the beginning of 1943 by the new type Sp12R. There were two types of ignition switches mounted - the switch of the HASAG company had a longer cast metal key were the Hella one, used from end 1939 onwards too, had a pressed-metal key.

There were two types of exhaust systems mounted - Eberspaecher and Leistritz. The latter was recognisable for the wider fish-tail end.

The DKW build Framo seat was used alongside with the new Pagusa type.

NZ350 Gelaendesport

At the end of 1938 also an "off-road version" of the NZ was available for a price increase of 40,00 RM. These bikes were fitted with a raised exhaust system, axles with "quickchange" handles, the dynamo guard, but not with off-road tyres!

NZ350 Gelaendesport

From 1939 on NZ was also available in a version for the government, which later became the NZ 350/1943 and finally the NZ350-1.

In June 1940 the rear end of the bike was shortened with 40 mm (from frame number 582559), which lifted the rear seat with 4 mm.

In early 1941 the production of the NZ 250 stopped. The NZ 350 continued to be build for Wehrmacht use only (from VIN 595200 onwards only NZ 350's were build). At the same time the gearbox was reinforced and the gear-ratio was changed to facilitate driving at low speeds in a convoy. The reinforced gearbox can be identified by the letters VG "verstaerktes Getriebe" on the engine case from engine number 1180601.

From NZ 350 to NZ 350-1

During the war the production of the company was restricted from the spectrum 125 - 500 cc of different types to just two models - NZ 350/NZ 350-1 and RT 125.

The NZ 350 was adopted for army service and became the "middle-class 350 cc motorcycle" in the Wehrmacht's catalogue. The machine soon became known as "Das Motorrad der Kradmelder" - the dispatch rider's motorcycle.

In 1943 the standard NZ 350 received its first major facelift. Redesigned were the mudgards, a cyclone airfilter and a smaller headlamp. Officially this model was named NZ 350/1943.

In the beginning of 1944 another facelift was made, when the NZ 350/1943 received an engine block that was made from cast iron and number of other modifications. This model was named the NZ 350-1.

Specifications

Engine air-cooled 346cc, 1-cyl, 2-stroke
Horsepower 11.5 bhp@4000 rpm
Bore/stroke 72/85 mm
Compression ratio 5.7:1
Valves slit
Carburetor Amal M 76/426, Bing AJ 2/24, Graetzin H 24; 24 mm
Electrics 6 volts
Secondary drive chain
Length 209 cm
Width 75 cm
Saddle height 70 cm
Wheelbase 1355 mm
Clearance 12 cm
Transmission 4-speed
Shifting foot & hand
Frame pressed steel single, rigid rear end
Front fork Parallelogram
Weight 145 kg (aluminium block)
Brakes drum/drum
Top speed 105 km/h
Tires 3.25 – 19 inches
Fuel capacity 14 liters
Fuel consumption 3.3 liters /100 km
Overall amount 45 300 units
Years of production 1938 - 1943